ESAB MultiPower 460 Pulse Especificações Página 45
- Página / 64
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Manual 89250890 6-1 SYSTEM USES
SYSTEM USES N7500
SECTION 6:
N7500 SYSTEM USES
6.01 SYSTEM USES
This section briefly describes some uses for the N7500 System. If you have any questions concerning a specific
application for this system contact Victor Technologies Technical Services Department at 800-426-1888 or 940-
566-2000.
GOUGING NON-FERROUS METALS
The N7500 System can be connected to DC Straight Polarity (DCEN) to gouge non-ferrous metals, such as nickel,
copper alloys, etc. “Figure 6-1: N7500 DC Straight Polarity (DCEN)” shows the proper connections for the system
to run on DC Straight Polarity.
REMOTE PENDANT
PENDANT CONTROL BOX CABLE
N7500 Gouging System
Automatic Control
OK
TRV
JOG
STOP
TUNE
ROUGH
START
CONTROL BOX
TORCH HEAD CABLE
AIR HOSE
DC POWER
CABLE (+) OUT
TORCH HEAD
GROUND CABLE (–)
DC POWER CABLE (-) IN
INCOMING
AIR LINE
POWER
SUPPLY
TORCH HEADPENDANTAIR OUT
MOUNTING
FIXTURE
AIR INLET
ART# A-10852_AC
POWER SUPPLY
COMMUNICATION CABLE
AIR REGULATOR
WORK PIECE
SIGNAL
WIRE
GROUND CABLE (+)
CONTROLLER INPUT
AC POWER CABLE
CONTROL BOX
(VIEWED FROM CABINET RIGHT SIDE)
120V
OR
220V
N7500
(Rear panel assembly
not shown for clarity)
5 AMP
5 AMP
THESE CONNECTIONS
ON OTHER SIDES
Figure 6-1: N7500 DC Straight Polarity (DCEN)
NOTE
Use standard #12 insulated copper wire as your signal wire. It must be long enough to prevent stress
on the Contactor connection.
6.02 Zero Force Rough Machining
The N7500 system can work with an automated travel system to remove hardsurfacing material from steel mill
rolls; kiln rolls and shafts which needs re-working. Remove as much as 1-1/2” (3.81 cm) of old material from the
outside diameter in a single pass and as little as 1/8” (3.18 cm) for the finish pass.
OSCILLATION GOUGING TO REMOVE MATERIAL
The N7500 can be mounted on a welding oscillator to remove material. Normal uses for an oscillated gouge would
be to remove cladded material from plates requiring a beveled edge and to remove backup bars and excessive
weld crowns.
- Operating 1
- WE APPRECIATE YOUR BUSINESS! 2
- YOU ARE IN GOOD COMPANY! 2
- TABLE OF CONTENTS 4
- Figures and Tables 6
- SECTION 1: 9
- GENERAL INFORMATION 9
- N7500 GENERAL INFORMATION 10
- GENERAL INFORMATION N7500 11
- This Page Intentionally Blank 14
- SECTION 2: 15
- SPECIFICATIONS 15
- N7500 SPECIFICATIONS 16
- SECTION 3: 17
- SYSTEM COMPONENT DESCRIPTION 17
- Item Fitting Function 18
- ART# A-10853_AB 19
- 3.02 Torch Head 20
- 3.03 Remote Pendant 22
- 3.04 Electrodes 23
- Diameter 25
- 3.07 Keeping Electrodes Dry 25
- 3.09 Compressed Air 26
- 3.10 Main Air Line 26
- ART# A-10855_AC 27
- ART# A-10838_AB 27
- ART# A-10865_AC 27
- Art# A-10845_AC 28
- Art# A-10857_AB 28
- Art# A-10849_AB 28
- MAX 100 p 28
- ART# A-10924_AC 28
- 4.02 Assembly 29
- CONTROL BOX 30
- CONTROL BOX POWER SUPPLY 31
- (Rear panel assembly 33
- TORCH HEADPENDANTAIR OUT 33
- THESE CONNECTIONS 33
- ON OTHER SIDES 33
- 4.07 Remote Pendant Storage 35
- ART# A-10856_AB 37
- N7500 SYSTEM OPERATION 38
- ART# A-10825_AC 39
- ART# A-10826_AC 39
- ART# A-10824_AC 41
- ART# A-10828_AB 42
- SYSTEM OPERATION N7500 43
- N7500 SYSTEM USES 46
- SECTION 7: 47
- MAINTENANCE 47
- 0.0HRArctime 48
- NoCurrent Detect 48
- SECTION 8: 49
- TROUBLESHOOTING GUIDE 49
- N7500 TROUBLESHOOTING GUIDE 50
- TROUBLESHOOTING GUIDE N7500 51
- MAX 100 psi 55
- ART# A-10843_AC 56
- ART# A-10835_AB 57
- SYSTEM CABLES 58
- Manual 89250890 A-1 APPENDIX 59
- APPENDIX N7500 59
- Manual 89250890 A-2 APPENDIX 60
- N7500 APPENDIX 60
- 10.01 Wiring Schematic 60
- Manual 89250890 A-3 APPENDIX 61
- PUBLICATION HISTORY 62
- 1 Month Harness Assy 63
- THE AMERICAS 64
- ASIA/PACIFIC 64
Manuais e produtos relacionados com Sistema de solda ESAB MultiPower 460 Pulse
Sistema de solda ESAB ESP-101 Manual de Serviço
(40 páginas)
(40 páginas)
Sistema de solda ESAB PCM-750i Manual do Utilizador
(12 páginas)
(12 páginas)
Sistema de solda ESAB ESP-50 Manual de Instruções
(56 páginas)
(56 páginas)
Sistema de solda ESAB ESP-101 Manual de Instruções
(80 páginas)
(80 páginas)
Sistema de solda ESAB POWERCUT-1500 Especificações
(48 páginas)
(48 páginas)
Sistema de solda ESAB PCM-875A Manual de Instruções
(48 páginas)
(48 páginas)
Sistema de solda ESAB ST-16 Manual do Utilizador
(2 páginas)
(2 páginas)
(44 páginas)
Sistema de solda ESAB ESP-50 Manual de Instruções
(22 páginas)
(22 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais